If you’re here its safe to assume that you are confused about how to cut a flagstone with your circular saw.
However, it is not impossible to do so. If you want to do it yourself, we suggest that you go through this detailed guide thoroughly before you get started.
This guide includes all the necessary information, instructions, tips, and FAQs to assist you along the process.
Quick Summary
This guide will help you with all the relevant detail about
- How to cut flagstone?
- What things are needed to be considered?
- A detailed FAQs section.
How to Successfully Cut Flagstone with Circular Saw - In-Depth Guide
To successfully cut flagstone according to your choice, we have added all the necessary instructions after thorough research.
Moreover, you have to be mentally prepared for this hectic job as you will do it on your own. There are some things you need to consider before you start the process.
Things You Need to Consider Before You Cut Flagstone with Circular Saw
Cutting flagstone can be quite dangerous, make sure you have all the safety gear ready before you hop into it. The safety gear includes:
-
- Working gloves: They are thick gloves that protect your hands from any sharp edges.
- Work pants: They are a special type of pants made from denim and polyester.
- Safety goggles: They help protect the eyes from any flying debris or particle.
- Face shield: This is preferred over safety goggles as it shields your whole face.
- Earmuffs: They help avoid any damage from high construction work sounds.
- Dusk mask: This is optional but can provide extra protection to your lungs.
These will help you protect your face, eyes, hands, and legs from any potential damage or mishap.
How to Cut Flagstone with a Circular Saw – Step-by-step Guide
This section is the most important part of the guide, make sure you follow all these steps carefully to avoid any mishap.
This guide will assist you along the process and will make sure you do everything perfectly.
Without any delay, let us start with our first step.
Step 1: Wear Your Safety Gear
This step is very important to make sure you are safe. A circular saw is very helpful but dangerous at the same time.
Make sure you wear every component of safety gear and do not skip any of it.
Tip: We also prefer you wear a dust mask so you do not inhale any dust particles. This can be very harmful to your lungs.
Step 2: Change to Diamond Masonry Blade
Circular Saw is a very versatile tool as it helps cut all kinds of materials such as wood, brick, concrete, flagstone, and many more.
However, to cut any material smoothly you should install the right blade for it. We recommend you change your current blade to a diamond masonry blade.
Tip: Do this step beforehand as it will save you the actual process time. You have to remove the bolt and washer to remove the current blade from your circular saw.
Make sure you insert the diamond masonry blade and secure the bolt and washer firmly.
Step 3: Adjust the Depth of Your Circular Saw
You have to set the depth of the circular saw so it can cut through ¼ of an inch as it is preferred. It is set with a help of a lever attached to one of the sides of your circular saw.
However, it can vary from model to model so make sure you see the manual and do it accordingly.
Tip: This step is very important as the RPM of the circular saw is affected by it.
Step 4: Mark the Measurements on Your Flagstone
First, you have to measure the spot where you will fit your flagstone. Use chalk to mark your measurements on the flagstone precisely.
Moreover, fit your flagstone tightly so it does not slide when you are cutting it with the circular saw.
Tip: We recommend you use chalk instead of a pen or marker, as both of these can stain your flagstone. Chalk is easily washed off.
Step 5: Set the Flagstone
Make sure you set the flagstone on a flat surface. The spot which needs to be cut should be on the platform and the remaining should keep hanging.
Tip: If the cutting spot is flat all the time, the flagstone will be cut very precisely.
Step 6: Cut the Flagstone Carefully
This step is where all your effort is to be used. Lower your circular saw and gradually push it towards the chalk markings to cut it precisely.
Moreover, flip your flagstone and do the same. Make sure you do not apply extra pressure this can make deep cuts which can damage your flagstone instantly.
Warning: If you put extra pressure, it can also stimulate dangerous kickbacks that can cause fatal injuries.
Step 7: Break the Remaining Part
You should have a hammer and chisel to finish the final job. It is difficult to cut the whole flagstone with a circular saw only.
Therefore, break down the remaining part of the flagstone by hammering it down.
Find more resource guides for your favorite tools HERE.
Frequently Asked Questions (FAQs)
We have also added this FAQs section to further help you with any confusion you might have.
What is the best way to cut the flagstone?
You should mark the measurements on the flagstone with chalk. Cut the flagstone by gradually applying pressure.
What kind of saw is best suited to cut flagstone?
There are many types of saws that can be used to cut flagstone such as a handheld tile saw, wet table saw, and many more.
However, we have tested a circular saw that uses a diamond masonry blade to cut flagstone and it works the best for precise cuts.
How do you break irregular flagstone?
For irregular flagstone, you should use a hammer and chisel to make all the necessary cuts and break its smaller pieces.
However, if you want regular shapes like a square or rectangle. You should have a circular saw with a diamond masonry blade for it.
To Conclude…
We understand that cutting flagstone with a circular saw is quite a tiresome and dangerous task.
However, it is not impossible. We have compiled this guide that might help you do it on your own.
This guide has all the necessary information, instructions, tips, and FAQs to make this process as easy and safe as possible.
We hope this guide helped you, feel free to contact us anytime. Visit our website.